جمالی, کریم, اکبری, داود, گلزار, محمد. (1396). ارزیابی غیر مخرب حرارت نگاری مادونقرمز مدولهشده در عیبیابی مواد مرکب زمینه پلیمری. مهندسی مکانیک مدرس, 18(2), 225-233.
کریم جمالی; داود اکبری; محمد گلزار. "ارزیابی غیر مخرب حرارت نگاری مادونقرمز مدولهشده در عیبیابی مواد مرکب زمینه پلیمری". مهندسی مکانیک مدرس, 18, 2, 1396, 225-233.
جمالی, کریم, اکبری, داود, گلزار, محمد. (1396). 'ارزیابی غیر مخرب حرارت نگاری مادونقرمز مدولهشده در عیبیابی مواد مرکب زمینه پلیمری', مهندسی مکانیک مدرس, 18(2), pp. 225-233.
جمالی, کریم, اکبری, داود, گلزار, محمد. ارزیابی غیر مخرب حرارت نگاری مادونقرمز مدولهشده در عیبیابی مواد مرکب زمینه پلیمری. مهندسی مکانیک مدرس, 1396; 18(2): 225-233.
ارزیابی غیر مخرب حرارت نگاری مادونقرمز مدولهشده در عیبیابی مواد مرکب زمینه پلیمری
1گروه مهندسی ساخت و تولید، مهندسی مکانیک، دانشگاه تربیت مدرس، تهران
2استادیار- دانشکده مهندسی مکانیک - دانشگاه تربیت مدرس
3دانشیار دانشگاه تربیت مدرس تهران مدیر گروه مهندسی ساخت وتولید
چکیده
در این مقاله به ارزیابی حرارتنگاری مادون قرمز مدولهشده در شناسایی عیوب زیر سطحی مواد مرکب زمینه پلیمری پرداخته شده است. در این روش به منظور تحریک نمونه، شار حرارتی به صورت متناوب به سطح قطعه اعمالشده و پاسخ حرارتی به وسیله تبدیل فوریه پردازش و تصاویر دامنه و فاز استخراج میشوند. پسزمینه غیریکنواخت مشاهدهشده در تصاویر حاصل، اغلب قدرت تشخیص را پایین میآورد لذا برای بهبود ارزیابی این روش، فیلتر آشکارساز لبه و ریختشناسی توصیفی بر روی تصاویر اعمال میگردد. بررسی تجربی در فرکانسهای مختلف بر روی نمونههای ساختهشده با نقصهای کنترلشده رایج در مواد مرکب صورت گرفت. از تحلیل نتایج برای تعیین دقیق موقعیت و ابعاد عیوب استفاده و مشاهده شد که در نمونههای با ضخامت 2 میلیمتر نقص جدایش بین لایهای با حداقل اندازه 20*10 میلی متر و نقصهای الیاف خشک و نفوذ مواد ناخواسته با حداقل اندازه 50*40 میلیمتر شناسایی و اندازهگیری میشوند. در تحلیل اجزای محدود هندسه و عیوب به کار برده شده در آزمون تجربی، در نظر گرفته شد. مشاهده شد که نتایج ارزیابی اجزای محدود با ارزیابی تجربی مطابقت داشته و میتواند در یافتن متغیرهای بهینه در بررسی حرارتنگاری مادون قرمز مدولهشده در عیبیابی مواد مرکب به کار گرفته شود.
Non-destructive Investigation of Modulated Infrared Thermography in Evaluation of Subsurface Defects in Polymer Matrix Composites
نویسندگان [English]
karim jamali1؛ Davood Akbari2؛ mohammad Golzar3
1Department of Mechanical Engineering, Tarbiat Modares University, Tehran, Iran
2Mechanical engineering-tarbiat modares university
3Department of Mechanical Engineering, Tarbiat Modares University, Tehran, Iran
چکیده [English]
In this paper, an investigation was done on modulated IR thermography for detection and evaluation of artificial subsurface defects in composite materials. In this method, In order to stimulate the test specimen, the heat flux is applied periodically over the surface of the specimen and the thermal response is decomposed by the Fourier transform method in order to extract its amplitude and phase images. The non-uniform backgrounds in the obtained images often reduce detection ability, In order to improve the evaluation of this method, an edge detection filter and a morphological attribute profile were applied to the images. Experimental investigations were applied for different frequencies on specimens made with common controlled defects in composite materials. Interpretation of the results were utilized in the calculation of defects’ size and location, it was observed that in specimen with 2 mm thickness delamination defect with a minimum size of 20*10 mm, dry fiber and inclusion defects with a minimum size of 50*40 mm is detected and is measured. The same geometry and the artificial defects used in experiments, were considered in the finite element analysis. The results of finite element analysis were found to have an agreement with the experimental results and can be used to find the optimum parameters in investigation of modulated IR thermography for detection of defects on composites.